Standalone Round-Tube Tree Column: Φ350 Base Plate, 8×Φ33 Anchor Holes, 8 Radial Gussets, Q235B

2026-11-16 18:18:32

Standalone Round-Tube Tree Column: Φ350 Base Plate, 8×Φ33 Anchor Holes, 8 Radial Gussets, Q235B

English Version

Title: Standalone Round-Tube Column: Q235B Shaft, Y-Shaped Top, Φ350 Base Plate with 8×Φ33 Anchor Holes

Data note: the supplied screenshots are low resolution. Tube OD/wall, plate thicknesses, lengths and the exact column mark are not legible; the figures below come only from what could be read on the drawings. Confirm every section against the original shop BOM before quoting.


blog-132-364


Overview

This is a standalone round-tube column. One round steel tube forms the shaft; the top branches into two inclined round-tube legs in a Y shape to pick up two framing members. The bottom sits on a circular base plate with radial gussets and anchor bolts. The BOM grade column reads Q235B on every member.


Readable Drawing Data

 

Item Value
Column type Standalone round-tube tree column (Y-branched top)
Steel grade Q235B
Base plate Circular, Φ350 mm
Anchor bolt holes 8 × Φ33 mm
Base stiffeners 8 radial gussets between shaft and plate
Bolts M24
Section view B-B, scale 1:10
Tube OD×wall, plate sizes, lengths Not legible in screenshot — see original BOM

BOM Parts Readable on Drawing

 

Part mark Role Grade Spec / length
J-1 Main shaft / upper member Q235B Original BOM
J-1 Small top fitting Q235B Original BOM
J-2 Branch member Q235B Original BOM
P-1 Base plate / main plate Q235B Original BOM
P-2 Connection plate Q235B Original BOM
P-5 Gusset plate Q235B Original BOM
P-7 Stiffener plate Q235B Original BOM
P-8 Small fitting plate Q235B Original BOM
P-9 Small fitting plate Q235B Original BOM
加劲板 Stiffener set Q235B Original BOM
螺栓 Anchor bolts M24 Original BOM

Unit and total weights were not reliably legible in the screenshot; do not use the blurred weight figures from this image in a quotation.


How the Column Works

The round shaft carries axial load. A circular tube handles compression and tension evenly around the section and resists torsion better than an open angle or channel.

The Y-head splits the reaction. Two inclined branches transfer load from two framing members into the single shaft; branch-to-shaft joints carry both axial force and local bending.

The base plate spreads the reaction. The Φ350 circular plate distributes the column force to the foundation; eight gussets tie the shaft wall to the plate and control local bending at the foot.

Anchor bolts fix the foot. Eight Φ33 holes take the M24 anchor bolts; the bolt group resists uplift and horizontal shear at the base.


Advantages

Circular section resists wind and torsion — round tubes have low drag and no weak axis; suitable for exposed standalone columns.

Clean visible form — a round shaft and Y-head read well in canopies, entrance frames, and outdoor structures.

Light per tonne of capacity — a tube uses material around the perimeter; compared with a solid or plate-built column it keeps the footprint small.

Simple base detail — circular plate, radial gussets, and a bolted anchor group are straightforward to fabricate and inspect.

Standard Q235B material — common structural grade, easy to source and weld.


Disadvantages / Limitations

Tube interior cannot be inspected — closed shafts need end sealing, venting, and coating before closure; inside corrosion is invisible afterwards.

Branch joints need detail work — the Y-head tubes are cut to angle and welded to the shaft; fit-up and weld quality control the joint capacity.

Base local bending — gusset spacing and plate thickness must match the reaction; an under-sized plate or missing gusset shows at the foot.

Slenderness check matters — a long thin tube shaft is checked as a compression member; buckling governs before yield for a light column.

Section and weight must come from the BOM — the screenshot does not show tube diameter, wall thickness, or shaft length; capacity and weight cannot be calculated from this image alone.


blog-297-176

Typical Use Cases

Entrance canopy and porch columns — Y-head picking up two roof beams.

Outdoor standalone support columns — pergolas, walkways, and open frames.

Industrial platform and equipment supports — round shaft on a bolted base plate.

Tree-style frame columns — one shaft branching to several upper members.

Retrofit or replacement columns — base plate and anchor group matched to an existing foundation.


Fabrication and Erection Notes

Material: Q235B; verify mill certificate against the original BOM.

Shaft: confirm tube OD×wall and shaft length from the shop drawing before cutting.

Y-head: cut branch tubes to the true angle; check joint fit-up before welding; weld around the branch-to-shaft connection.

Base: check Φ350 plate, eight radial gussets, and 8×Φ33 anchor hole positions; match the M24 bolts to the foundation design.

Protection: seal tube ends, provide vent/drain holes, and coat the exterior per the project corrosion requirement.

Erection: set the base plate to the anchor bolts, plumb the shaft before fixing branches, and brace the column before releasing the crane.


blog-198-234


Bottom Line

A Q235B standalone round-tube column with a Y-branched top and a Φ350 circular base: eight Φ33 anchor holes, eight radial gussets, M24 bolts. The round section resists load evenly and looks clean exposed. Tube size, wall, length, and weight must be read from the original BOM — this screenshot does not carry those numbers.

**WhatsApp**: +86‑13889862778, +86‑18242444407
**Email**: eddie@zdsteels.com, wells@zdsteels.com

Previous article: Galvanized Round-Tube Truss: Q235B Chords, Welded Nodes, Bolted Connection Plates

YOU MAY LIKE